Home > Cruise Control > Volvo V70 Cruise Control

Volvo V70 Cruise Control


If test verifies cruise control switch is okay, connect voltmeter (backprobe) between cruise control selector switch connector terminal No. 4 (White/Black wire) and ground. Connect voltmeter between ground and cruise control unit base terminal 8T. If voltage is about 10 volts, diagnostic wire is okay. The cruise will not work for me either. this contact form

Let me know the details and I'll give it a go.... JBC Reply With Quote 08-24-2010,09:17 PM #12 JBC View Profile View Forum Posts Private Message View Blog Entries Junior Member Join Date Aug 2010 Posts 37 Chris, I have not forgotten If voltage supply is present, replacebrake light switch. Otherwise, control unit terminal 9T did not have battery voltage at moment of disengagement. http://volvoforums.com/forum/volvo-s70-33/cruise-control-wont-set-13261/

Volvo V70 Cruise Control

Quote Postby BobbyC » Fri Oct 29, 2010 2:30 am I thought "Engine System Service Required" was a reminder for routine oil service every 5000mi?Any way, my cruise has been very Main function of control unit is to decide if system can be controlled based on values and status of input signals, and to regulate system for optimal function. If battery voltage is not present, ensure voltage supply is present at brakelight switch. Forgot Password?

Forum Technical General Technical Help cruise control not working If this is your first visit, be sure to check out the FAQ by clicking the link above. Need help? Fig. 1: Identifying Cruise Control Main Switch & Connector Courtesy of Volvo Cars of North America. Volvo S80 Cruise Control Not Working See SELECTOR SWITCH TEST (RESPONSE CODE 1-1-3).

Turn ignition on. If battery voltage is present, go to next step. Connect other wire end to terminal 7S.

Otherwise, control unit terminal 6S was not connected to ground through brakelight bulbs at moment of disengagement.

Brakelight Switch Check (Response Code 1-3-2) 1) Step on brake pedal. Volvo S60 Cruise Control Fault See SELECTOR SWITCH TEST (RESPONSE CODE 1-1-3). Although highly unlikely, it's another possiblity. __________________ - Drew - 98 S70 T5M B&G springs, Koni sports, Custom 3" turbo back exhaust, Precision Turbo FMIC, Stern 18's http://smg.photobucket.com/albums/v212/fastredponycar/Volvo/S70/ #4 Speed Below Minimum/No Signal 2-1-1 ………….

  1. hmmmmm 5labJun 28th, 2005, 16:33are you sure you're using it correctly?
  2. No special tools required.FYI: The region which these photos refer to is on the driver side, directly under the brake fluid reservoir.
  3. Robert DIY 112.830 visualizaciones 17:22 How To Test A Volvo Throttle Position Sensor - Duración: 4:26.
  4. Elige tu idioma.
  5. Road test must be repeated.
  6. Make sure the wire harness is attached snugly and that the elbow is attached snugly onto the vacuum pump.

Volvo S70 Cruise Control

The time now is 06:06 AM. -- volvo37 Contact Us - Volvo Forums - Volvo Enthusiasts Forum - Archive - Advertising - Cookie Policy - Privacy Statement - Terms of Service Register. Volvo V70 Cruise Control See TRANSFER RATE TEST CODES table. Volvo S40 Cruise Control Not Working Inicia sesión para añadir este vídeo a una lista de reproducción.

Reply With Quote 09-09-2010,11:33 PM #24 Wayne T5 View Profile View Forum Posts Private Message View Blog Entries Member Join Date Nov 2002 Location Russell Twp, OH Posts 6,141 I think weblink To start viewing messages, select the forum that you want to visit from the selection below. I've just purchased a 2001 Volvo C70 T5 and am made up with it... Often times a non-cel code is stored that can tell you what sensor is causing your cruise to fail. Volvo Xc90 Cruise Control Not Working

But using the minus side of the rocker sets it fine. is this what you seek?~ 1 out of 1 people think this is helpful. WIRING DIAGRAMFig. 6: Cruise Control System Wiring Diagram (1995-96)Disclaimer: Volvotips has the exclusive courtesy of Volvo Car Corporation and Volvo Cars Heritage to publish the Volvo Greenbooks (service manual), parts catalogs http://wiiemulator.net/cruise-control/volvo-s60-cruise-control-fuse.html Ohmmeter should show about zero ohms.

Air is pumped out through right coupling. Volvo Truck Cruise Control Not Working my cruise doesn't work, it use to, the light doesn't even come on when I flip the switch, so I'm wondering if I have a broken wire. See Fig. 4.

the fuse is fine and didnt know if anyone had any ideas.

Ben. Krimson37 1.827.831 visualizaciones 4:18 Why do I like Volvo's and what do I look for when looking to purchase one. - VOTD - Duración: 30:36. This test function can be used when cruise control disengages without driver input. If voltmeter indicates battery voltage, replace cruise control selector switch.

If this code is set without shift lever in one of these positions, control unit terminal 3T was grounded at moment of disengagement. Liam Hutton 2.731 visualizaciones 2:45 Cargando más sugerencias... Yes, my password is: Forgot your password? his comment is here Code 2-1-2 Code 2-1-2 is stored if there is short circuit to ground or voltage in circuit to vacuum pump and regulator.

IpdVolvo 127.928 visualizaciones 4:16 Repairing a cruise control - How a cruise control works - Duración: 1:59. Step on brake pedal. Robert DIY 39.796 visualizaciones 10:02 ipd Volvo - 850 Odometer Gear - Duración: 12:46. If system operates as described, go to next step. 3) Let vacuum servo remain contracted for at least 30 seconds to ensure there is no leakage in vacuum system.

rspi Off Topic 13 03-07-2010 07:13 PM Cruise Control Won't Quit! If you have not received your password reset email please use the password reset function forgot password. The "ENGINE SYSTEM SERVICE REQUIRED" message can often yield OBD2 codes, usually for O2 or MAF problems. Replace valve. 8) Start vacuum pump again and contract vacuum servo.

See Fig. 2.SYSTEM TESTSNOTE: Diagnostic unit for retrieving codes is located in right front section of engine compartment. Stop vacuum pump when vacuum servo is fully contracted, but keep regulator connected. Switch to another language: Catalan | Basque | Galician | View all Cerrar Sí, quiero conservarla. No, create an account now.

Connect ohmmeter between control unit base terminals 7T and 9S.