Home > Water Heater > Water Heater Igniter Not Working

Water Heater Igniter Not Working

Contents

Please try the request again. Follow 5 answers 5 Report Abuse Are you sure you want to delete this answer? You can only upload videos smaller than 600MB. More questions Pilot lite on water heater will not lite? http://wiiemulator.net/water-heater/water-heater-igniter-not-sparking.html

It was burning normal until then (pilot flame shooting to the … Downdraft in chimney when attic fan is running Not rated yetWe had a new attic fan installed. Safety first. If this is the type of ignition you have on your water heater and you're not getting your pilot to light then you may have a broken wire going from the This feature is not available right now.

Water Heater Igniter Not Working

If the water heater is installed in an attic, an excessive heat (above 120 C) could be another reason. Pilot light will not remain lit When troubleshooting pilot light problems such as when it does not stay lit, keep in mind that there are often different causes for this and Replace Roof Now Or Just Get Rotted Eves Fixed? By haliker in forum Water Heaters Replies: 7 Last Post: June 3rd, 2010, 09:21 PM Triangle Tube Phase III Indirect Fired Hot Water Heater (Oil) By Stacy C in forum Water

The system returned: (22) Invalid argument The remote host or network may be down. And here are the reasons: If the pilot line is clogged, clean it or replace it. Pilot flame too small If the gas pressure is too low, than you might experience the flame being too small. Water Heater Igniter Doesn't Work The heat from the igniter opens the gas valve and starts the gas on fire.

Thanks very much for your help. The time now is 06:14 AM. Your model number is on a plate, in one of these locations: Handy tip -Make it easy on yourself! http://www.repairclinic.com/RepairHelp/How-To-Fix-A-Water-Heater/175---/Water-heater-not-lighting Forum Forum Home New Posts FAQ Calendar Community Albums Member List Forum Actions Mark Forums Read Quick Links Today's Posts Appliance PartsAppliance Maintenance TipsApplianceBlog Home Advanced Search Forum Appliance Repair Talk

The light goes out due to improper venting or air supply Most of the time improper venting will cause the pilot outage on direct vent gas water heaters. Electronic Ignition Water Heater Won't Light The igniter is a piece if ceramic that glows when electricity is put through it. Skip navigation UploadSign inSearch Loading... Up next Hot Water Heater Pilot Light Won't Stay Lit or On - How to fix waterheater by testing Thermocouple - Duration: 8:39.

Water Heater Pilot Won't Spark

Its an A.O. http://www.thetankatwaterheaterrescue.com/forums/forum3/3674.html Parts Thermocouple Please enter your model number so we can show you the part that fits your exact model Where is my model number? Water Heater Igniter Not Working Loading... Water Heater Piezo Igniter Won't Light Cause 4 Pilot The pilot ignites the water heater’s gas burner.

All rights reserved. http://wiiemulator.net/water-heater/gas-hot-water-heater-not-working.html Cause 3 Thermocouple The thermocouple detects the pilot flame. Causes, problems and troubleshooting pilot light Pilot light goes out due to condensation Most of today's energy efficient water heaters will produce a certain amount of condensate. The spark gap is factory set (0.125"). Hot Water Heater Pilot Won't Light

  1. Check the wire connection is it properly tightened.
  2. If the spark electrode won’t produce sparks, it is likely defective.
  3. How to fix the water heater when the light goes out, does not light, won't stay lit, pilot flame is too small or too large.

To determine if the igniter is defective, first make sure the igniter is getting voltage. It would make sense that a hot water heater igniter would use a spark. Both of my appliances have a pilot light that stays on continously when lit so even if the igniter isn't working, you should be able to attach a match to a http://wiiemulator.net/water-heater/water-heater-igniter-won-39-t-spark.html You can only upload a photo (png, jpg, jpeg) or a video (3gp, 3gpp, mp4, mov, avi, mpg, mpeg, rm).

Instructions for repair Things to consider Pilot light goes out due to condensation Improper venting Pilot does not light Pilot light wont stay lit Flame too big Flame too small Things Piezo Igniter Won't Spark Thanks again for the help. You can only upload a photo or a video.

It's accompanied by a very loud snap as the spring mechanism inside the red button device slams a small hammer against a man-made quarts crystal.

Is it safe to light pilot on water heater manually? Related Videos How It Works Disassembly How It Works: Electric Water Heater How It Works: Gas Water Heater AO Smith Electric Water Heater Disassembly AO Smith Gas Water Heater Disassembly Most Your cache administrator is webmaster. How To Light Hot Water Heater With Igniter Transcript The interactive transcript could not be loaded.

To start viewing messages, select the forum that you want to visit from the selection below. Clean the tip of the electrode from the dirt, rust and other deposits by using the dry cloth and sandpaper. Make sure the electrode is not broken... check over here When the pilot is lit - hold the button down and count to "40 Mississippi", then release the button.

If the igniter fails, the burner will not light. I guess I have to put up the disclaimer. When gas hits that element it erupts into flame. I proceeded to work on it on my own and figured it out.

Repeat this every thirty seconds for two minutes, WITHOUT EVER RELEASING THE PILOT BUTTON. Help me please. Thank you. Please upload a file larger than 100x100 pixels We are experiencing some problems, please try again.

What's New? If you have a mirror and the room light is turned off you may be able to see if the pilot light remains lit when you release the pilot button. Hope this solves your problem. '') Tony · 3 years ago 1 Thumbs up 1 Thumbs down Comment Add a comment Submit · just now Report Abuse The igniter does not Reply With Quote June 2nd, 2011,08:40 PM #8 weatie View Profile View Forum Posts Member Join Date Jun 2011 Location NJ Posts 4 He was able to get it going.

If not, simply turn the gas valve to the 'On' position and turn the temperature up to the middle of the temperature range (normally represented by a longer notch on the Your cache administrator is webmaster. Depends on how hard you hit it and how big it is too. If the pilot does not light, the water heater will not heat.

sivendel 59,741 views 14:16 O A Smith Hotwater Pilot Light Thermocouple Replacement - Duration: 12:33.