Home > Water Heater > Water Heater Pressure Relief Valve Is Releasing Water

Water Heater Pressure Relief Valve Is Releasing Water

Contents

Today when I went into the basement, there was substantial water draining out of a long plastic tube leading from the hot water heater. Thank you! With the water to the house on, and water to the water heater shut off, I still get the sound of rushing water. MY question is, where did that water come from? http://wiiemulator.net/water-heater/electric-water-heater-no-hot-water.html

SIGN UP Invalid e-mail Advertise with us ADVERTISEMENT Follow Us Advertise with us ADVERTISEMENT Advertise with us ADVERTISEMENT We Recommend 20 Secret Hiding Places Save Money With Home Energy Audit Install Will we need to replace the T&P valve also or just remove and seal the connection better?? It's a propane run heater, if that makes a difference. If a water heater overheats to a temperature above 210 degrees F, building pressure inside the tank in excess of 150 psi, this simple little valve automatically opens and releases the

Water Heater Pressure Relief Valve Is Releasing Water

It was factory set at 124 F. Do I need to completely drain the hot water heater? The plumbing had been crossed. If you have an expansion tank it may have failed.

  • Turn off main.
  • I have never had an issue, a leak or any issue with it prior.
  • Should I call a plumber to have it checked?
  • Im not sure how old it is.
  • I checked and the water is not hot.
  • It must terminate 6"-12" above the floor, and the end cannot be threaded or have a fitting which permits connecting a plug or cap.
  • I never deflated the bladder pressure on this one.

Today's Homeowner Expert Advice on Improving Your Home Home Improvement Kitchen Remodel Cabinets Countertops Backsplash Sinks & Faucets More... or so it appears to be. Consult the chart at the home center store for proper tank sizing. Hot Water Heater Pressure Relief Valve Keeps Opening This happens on closed water systems ( check valve somewhere in the system).First replace your relief valve if it is an older one.

Any thoughts to help . Hot Water Heater Pressure Relief Valve Discharge Pipe Could an air bubble be stuck above the water in the expansion tank causing it not to work right? Loading... http://diy.stackexchange.com/questions/25218/what-causes-a-water-heaters-relief-valve-to-discharge-water Do I have to replace the heater, or is there anything I can do to fix the existing one?

kenny 3 YEARS AGO I replaced a leaking compression fitting valve and a faucet in an apartment and the next day the t&p valve gave out and will not hold pressure. Water Heater Pressure Relief Valve Installation Turn water and water heater (WH)on and a day later noticed it began to drip. It is electric. Where have you seen illustrations showing otherwise?

Hot Water Heater Pressure Relief Valve Discharge Pipe

The valve was just replaced but it didn't solve the problem. Paul Says: September 24th, 2010 at 12:10 am Am going to replace the valve, there are two to choose from, both have the same pressure specs, but one has a longer Water Heater Pressure Relief Valve Is Releasing Water elliott 4 YEARS AGO thank you Reuben for helping me and my situation. Water Heater Pressure Relief Valve Test The relief valve is on the side.

Jennifer Says: January 14th, 2010 at 12:49 pm I have attempted to change the TPR valve b/c it has a slow leak, I have followed all the steps, however I am this content I couldn't even make it to the ‘warm' setting before it began releasing the water. George Says: February 19th, 2011 at 10:08 pm Hi Marc, I have pooling from the inlet fittings on top of my (gas) hot water tank. I left it closed for 1 hour and then checked the gauge and it read 75 psi. Hot Water Heater Pressure Relief Valve Leaking After Replacement

Still leaks. What is the problem? I'm thinking the thermoster is corroded and acting as an insulator wich causes it to read temperature incorrect... weblink it has actually doubled my power bill.

I installed the new one with 58psi of air pressure and so far my water pressure has been steady at 58psi. Hot Water Heater Valve Shut Off I dont want to blow up my house. I live in nevada.

Now what to do to fix.

There is a tee fitting on top of the heater and the T&P valve is on the top with a line going in the wall and another line out the other Reuben Saltzman 4 YEARS AGO Angela - did you read this post? There is an expansion tank installed in the cold water inlet line that sits above the pipe. Water Heater Pressure Relief Valve Home Depot Should I just change the TPR valve?

smith. Is there a way to add air to the expansion tank? We just replaced a 19 year old water heater that dripped just a bit from the relief valve. check over here If the leak is coming from the threads around the pressure relief valve, then you need to use the proper thread sealant or tape when installing the valve.

The T&P valve was running and the drip was unabsorbed water by the insulation blanket. And don't test it at 10 PM on a Saturday night. :-) These valves are cheap and there's only one problem replacing them -- sometimes they're hard to unscrew. Is this a hjeater going bad or is there a fix for the issues mentioned. Pressure Most T&P valves are set to open at 150 psi.

todd Says: August 17th, 2012 at 5:51 pm its friday and i cant get a plummer here til next week,pressure vavle shot,can i cork the other end and be safe thru This comes and goes, I haven't called anyone since it may not hapen when they come out. After reading your comments, I'm wondering if these are related problems. Reuben Saltzman 3 YEARS AGO Hi Moe, I'm not sure.

Thanks for sparking the thought process for me! Just this one at the outside threads to pipe. Because it has attracted low-quality or spam answers that had to be removed, posting an answer now requires 10 reputation on this site (the association bonus does not count). Reuben Saltzman 4 YEARS AGO Hi Andrea, it sounds like either the t&p valve wasn't properly replaced or the water heater itself is leaking.